Proface HMI Communication Cable USB GPW CB03

Description

The Proface HMI Communication Cable USB GPW CB03 uses the serial signal through USB interface HMI programming cable, driver controlled computer running, USB intersection, computer simulation to traditional serial port (commonly known as COM port), then programming software, communication software and existing variety of software.

GPW-CB03 touch screen for Proface (GP37-2000), especially suitable for interference in the communication port, easily damage the circuit in large industrial field, various protective systems to ensure the safe operation of the system. GPW-CB03. If you Need proface hmi programming cable Price in BD you can Contact BAT Power Solution.

Common Proface HMI Programming Cable

1. CA3-USBCB-01 Programming Cable (USB)
   • Cable Type: USB programming cable.
   • Cable Model: CA3-USBCB-01 is a commonly used USB cable for Proface HMIs.
   • Connector Type:
     • One end has a USB Type-A connector (to connect to the PC).
     • The other end has a USB Type-B or Mini-B connector (depending on the HMI model).
   • Driver Requirement: Requires a USB driver, which can be downloaded from the Proface website.
   • Use Case: Used for connecting modern Proface HMIs to a PC for programming. This type of connection is simple and provides high-speed communication.
2. GPW-CB02 Programming Cable (RS-232)
   • Cable Type: RS-232 communication cable.
   • Cable Model: GPW-CB02 is an RS-232 programming cable used for connecting Proface GP series HMIs to a PC.
   • Connector Type:
     • One end has a DB9 female connector (to connect to the PC’s serial port).
     • The other end is a mini-DIN 8-pin connector (for the HMI).
   • Use Case: Used for older Proface GP series HMIs that support RS-232 communication. If the PC does not have a serial port, you may need an RS-232 to USB adapter.
3. Ethernet Cable (Standard RJ-45)
   • Cable Type: Ethernet cable.
   • Connector Type: RJ-45 connectors on both ends.
   • Use Case: For Proface HMIs that support Ethernet communication. This is useful for fast communication and remote access, especially when programming over a network.
   • Requirements: The PC and HMI should be configured with compatible IP addresses and be on the same network.

Key Considerations When Choosing a Proface HMI Communication Cable USB GPW CB03

1. HMI Model:
   • Different models of Proface HMIs (e.g., GP series, AGP series, LT series) may require specific cables. Make sure you check the exact model to determine the appropriate cable.
2. PC Communication Port:
   • If your PC has a USB port, use the CA3-USBCB-01 USB programming cable for simplicity.
   • For older HMIs that use RS-232, use the GPW-CB02 cable. If your PC lacks an RS-232 port, an RS-232 to USB adapter will be necessary.
3. Driver Installation:
   • If using a USB programming cable, install the correct drivers, which can be downloaded from the Proface website. Proper driver installation is essential for the PC to recognize the HMI.
4. Cable Length:
   • Typically, USB and RS-232 programming cables are around 1.5 to 3 meters in length, which is sufficient for programming in most scenarios.

Specification of Proface HMI Communication Cable USB GPW CB03

Brand Name: AMSAMOTION/Others

Product model: GPW-CB03

Product name: Proface HMI programming cable for GP37-2000 USB cable

Product Series: GP37-2000

Product Type: Communication Cable

Support operating system: Windows2000 / Windows XP (WinNT4 / 95/98 / Me / DOS not supported)

Fully compliant with USB 2.0 specification

USB bus powered

Bad rate: 300bps ~ 1Mbps Bad rate automatically adjusts the value

UART Enforces Data Format: Data Bits: 8, Stop Bits: 1, 2, Parity: Aberrant / Even / No Parity

Support for long distance communication,

Maximum communication distance 2 km (9600bps pm)

Each PC supports multiple USB programming cables

Operating temperature: -20~75*C

Cable length: 3m

Windows XP Windows 7 32/64bit | GPW-CB03 Driver for Windows 10 32/64 Bit

HMI Programming software GP Pro EX V3.0 Lower Version

After plugging the Programming cable into the computer, then go to the device manager, check the cable COM Port, if found cable com port then open the software GP Pro EX and set the cable type RS232, If not found COM Port then you have to setup the cable driver CH340 or CH341. Then check again go to your computer device manager and check COM Port for Example COM1, COM3, COM4, COM5 etc.

How to determine which driver to install

Step 1: Insert the Proface HMI USB cable to HMI and Open the software Step 2. Open the computer’s device manager to see the port prompt.

Others Cable